EMU BLACK
ECUMaster EMU Black Standalone ECU – T-Jet Engine Management Solution
The ECUMaster EMU Black is a class-leading standalone engine management system, designed to control some of the most advanced and demanding engine configurations.
Developed as the successor to the proven ECUMaster EMU platform, the EMU Black incorporates extensive hardware and software improvements based on years of real-world motorsport, tuning and development experience.
It is suitable for a wide range of applications, including:
-
Race and competition vehicles
-
High-performance road cars
The EMU Black can control fuel injection, ignition and multiple auxiliary systems on engines with 1 to 6 cylinders, including applications equipped with:
-
Electronic drive-by-wire throttle
-
Variable valve timing – VVT
-
Boost control
-
Flex-fuel systems
-
Launch control
-
Traction control
-
Anti-lag strategies
-
Water or methanol injection
-
Multiple fuel pumps and cooling systems
It can directly operate up to 6 passive ignition coils, without requiring additional ignition amplifiers or external power modules.
Its advanced drive-by-wire control strategies offer precise electronic throttle management, combined with extensive plausibility, fault detection and safety monitoring functions.
Free firmware upgrades continuously expand the ECU’s capabilities by adding new control strategies, trigger patterns, CAN-Bus data streams and additional features.
Complete ECUMaster EMU Black Solution for T-Jet Engines
SLP has developed a complete software solution for the installation and calibration of the ECUMaster EMU Black on Fiat and Abarth 1.4 T-Jet engines.
Customers can purchase the ECU directly through us and receive technical support for selecting the correct components and configuring the system according to their vehicle and performance requirements.
We can provide a ready-developed base calibration, allowing the installation and initial setup process to be completed significantly faster and more efficiently than starting a new standalone ECU project from zero.
The calibration can then be individually adjusted according to the exact engine setup, turbocharger, injectors, fuel system, sensors and intended use of the vehicle.Remote ECU Calibration
Remote calibration is also available for T-Jet vehicles located outside our workshop.
We can remotely configure and calibrate the ECUMaster EMU Black for virtually any level of T-Jet engine upgrade, following prior communication and a complete review of the vehicle specification.
Remote tuning can be provided for:
-
Standard or mildly upgraded T-Jet engines
-
Hybrid turbocharger setups
-
Garrett turbocharger conversions
-
Forged engine builds
-
High-power road vehicles
-
Track, hillclimb and race applications
Each project is evaluated individually, as the final calibration process depends on the vehicle specification, available sensors, fuel system, turbocharger, boost target and supporting modifications.
The Ultimate Engine Management Upgrade for T-Jet Engines
Installing an ECUMaster EMU Black is one of the most complete and effective engine management upgrades available for any T-Jet engine.
Compared with the limitations of the factory ECU, the EMU Black provides an extremely wide range of calibration and configuration possibilities.
This allows the tuner to achieve:
-
More accurate fuel and ignition control
-
Improved boost management
-
More stable engine operation
-
Better throttle response
-
Improved cold-start and idle behaviour
-
Advanced engine protection strategies
-
Individual safety limits based on oil pressure, fuel pressure, temperature, lambda and boost
-
Better control of highly modified or competition engines
-
Data logging and real-time engine monitoring
-
Greater flexibility for future upgrades
The result is not simply more power. It is a more precisely controlled, safer and better-functioning engine package.
Full Factory Instrument Cluster Functionality
When the ECUMaster EMU Black is combined with the compatible Interconnector module, which can also be supplied by SLP, the vehicle can retain normal operation of the factory instrument cluster and original dashboard systems.
Depending on the application and installation configuration, this allows the original vehicle instruments and indications to continue operating normally, including functions such as:
-
Engine speed display
-
Vehicle speed display
-
Coolant temperature indication
-
Warning and information signals
-
Factory dashboard communication
-
Additional original CAN-Bus functions
This provides the advanced control capabilities of a professional standalone ECU without unnecessarily sacrificing the functionality and appearance of the vehicle’s original instrument panel.
For ECU supply, Interconnector availability, installation requirements and remote calibration options, please contact us with the complete specification of your T-Jet vehicle and its current upgrade stage.
Payment & Security

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Description
GENERAL |
|
| Temperature range | AECQ100 GRADE2 (-40 to +105˚C) |
| Reverse battery protection | Yes, internal |
| Operating voltage | 6-22V, immunity to transients according to ISO 7637 |
| Enclosure | IP 60, custom CNC machined aluminium |
| Size (mm) and weight(g) | 150x72x31, 390 |
| Connectors | 1 x 24, 1 x 39 FCI Automotive connector |
| PC communication | USB (with PC client software), serial, CAN |
OUTPUTS |
|
| Injector outputs | 6 protected outputs 5A, low side |
| Ignition outputs | 6 outputs 7A(15A peak) (passive & active coils supported) |
| Aux outputs | 6 protected outputs 5A, low side |
| Other outputs | Full bridge up to 7A, can be used as separate outputs or 2 H-Bridges |
| WBO heater | Protected low side up to 5A |
| Communication | Serial, CAN BUS 2.0B |
INPUTS |
|
| Analog inputs | 9 inputs, resolution 10Bits, 0-5V (protected) |
| EGT inputs | 2 for K-Type thermocouple |
| Knock sensor | 2 inputs |
| Oxygen sensor | LSU 4.2, LSU 4.9 or Narrow band |
| Trigger inputs | 3 (primary, 2 cams) Hall/ VR software selectable |
| VSS | 1 (Hall / VR) |
| Flex Fuel Sensor | Yes |
| Switch inputs | 3 inputs, switched to ground |
SENSORS |
|
| Temperature sensors | IAT, CLT, Oil temperature, AC evap temperature |
| Pressure sensor | MAP, Oil pressure, Fuel pressure (user defined characteristic), AC pressure sensor, Back pressure |
| Oxygen sensor | LSU 4.2 or 4.9 (built in controller), Narrow band, external WBO controllers |
| Speed | Vehicle speed sensor (VR/HALL), Gear sensor (sensor, calculated) |
FUELING |
|
| Injectors | Up to 8 HiZ injectors (sequential) |
| Injection angle control | 0-720 deg, start or end of injections |
| Battery compensation | User defined, wizard for popular injectors |
| Fueling strategies | VE based speed density, Alpha N |
| Air charge temp. | Based on IAT and CLT |
| VE table | 2 tables 16×20 (Load x RPM), resolution of 0.1% |
| Individual cylinder trim | Yes |
| Staged injection | Yes |
| Additional correction | Oxygen sensor corrections, EGT correction (per cylinder), BARO, TPS vs MAP, TPS vs RPM, Warmup, Nitrous, LC, ALS, ASE, Fuel pressure, Knock sensor |
| Lambda based real time correction | Using Lambda target table |
| Acc. / Deceleration enrichment | Yes |
IGNITION |
|
| Ignition outputs | 6 for passive and active coils (software selectable) |
| Supported triggers | N-1, N-2, N-3, N+1, Multitooth, Subaru triggers, Nissan trigger, Lotus Elise, Audi trigger, Renault Clio Wiliams / Alpine, Colt 1.5CZ, Wrangler |
| Ignition angle table | 2 tables 16×20 (Load x RPM), resolution of 0.5 Deg |
| Per cylinder trim | Yes |
| Dwell time battery compensation | Used defined, wizard for popular coils |
| Odd fire compatibility | Application dependent |
| Additional correction | CLT, IAT, TPS vs MAP, Nitrous, Idle, Knock sensor, LC, Pit limiter, ALS, Flat shift, Timers, Acc. enrichment |
KNOCK SENSING |
|
| Channels | 2 |
| Resonant frequency range | 1-20kHz, 3rd order AAF |
| Sampling | Ignition event driven, knock window |
| Actions | Ignition retard, fuel enrichment, dashboard indication |
IDLE CONTROL |
|
| Control type | PWM solenoids (2,3 wires), drive by wire, stepper motors (bi and unipolar), ignition cut, fuel cut |
| Control strategy | Open / Close loop , ignition angle control |
| VE correction | Yes, for Alpha-N |
| Corrections | AC clutch, coolant fan, analog input |
BOOST CONTROL |
|
| Boost ref and target tables | 2 sets 10×10 (TPS vs RPM) |
| Control strategies | Open / Closed loop (PID based) |
| Corrections | Gear, VSS, IAT, EGT |
DRIVE BY WIRE |
|
| Control strategy | Advanced 3D PID + static friction compensation |
| Supported throttles | All with DC motor and current requirement lower than 6.5A
Wizard for 28 popular electronic throttles |
| PPS to throttle position characteristic | 3D table |
| BLIP support | Yes |
| ALS support | Yes |
TRACTION CONTROL |
|
| TC strategy | Delta RPM, gear compensation |
| Torque reduction | Spark cut using 3D table (16×20) |
| Sensitivity control | 10 position rotary switch |
VARIABLE VALVE TIMING |
|
| Supported systems | VVTi, MiVec, VANOS, Double Vanos |
| Number of camshafts | 2 |
| Control strategy | PID based closed loop, CAM angle target tables 12×12 |
FLEX FUEL |
|
| Ethanol content measurement | Yes |
| Fuel temperature measurement | Yes |
| Tables blending | VE, IGN, Lambda/AFR, Boost, Cranking fuel, ASE, Warmup |
| Fuel temperature PW correction | Yes |
SPORT |
|
| ALS | 2 independent ALS setting, DBW support |
| Shift light | Per gear shift light |
| Launch control | Yes |
| Gear cut | Yes (Open loop), DBW blip supported
Source: Switch, load cell, CAN |
| Pit limiter | Yes |
| Rolling anti lag | Yes |
ENGINE PROTECTION |
|
| Fail safe values for critical sensors | Yes |
| Dashboard indication of failures | Yes, user defined |
| Over temperature engine protection | Yes (oil and coolant), user defined, RPM limit |
| Low oil pressure protection | Yes, user defined, shut off |
| Fuel pressure protection | Yes, fuel dose compensation, RPM limit, engine shut off |
| High exhaust temperature | Alarm, per cylinder fuel trim, boost limit |
CAN BUS |
|
| CAN standard | 2.0B 125, 250, 500, 1000 kbps |
| Supported CAN Dashes | ECUMASTER, Motec M800 Set 1, Haltech E8 E11v2, Pectel SQ 6, AEM |
| Supported OEM CAN streams | BMW E46, Citroen C2, Mazda RX8, Ford ST, Polaris RZR, Mini Cooper R53, Fiat 500, Renault Clio, Lotus, Ford Fiesta, Ford ST, EVO X (AYC support) |
OTHER |
|
| Unused injection outputs can be used as AUX output | Yes |
| Output functions | Fuel pump, coolant fan, parametric outputs, nitrous control, PWM 3D table output, AC clutch, main relay, speedometer, tachometer |
| Password protection | Yes, 2 levels |
| Timers | Fuel, Ignition, Boost, timers controlled by virtual outputs |
| Serial dashboard support | AIM, RaceTechnology |
| Autotune | Yes |
| Built in trigger scope | Yes |
| Logging | Real time logging to PC computer, logging on external loggers (serial / CAN) |
Contact
User Account
Informations
Follow us on Social
